StorageTek 9840 Bedienungsanleitung Seite 78
- Seite / 250
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Rack
3-28 Sixth Edition 95741
CAUTION:
Equipment damage. Do not attempt to move the rack once drive or CSL
trays are installed. To prevent damage to the rack, you must remove all
drive/CSL trays and the stabilizer before relocating the rack.
Tools Required
The following tools are required to complete this installation:
• 1/2 in. open-end wrench
• 3/4 in. open-end wrench
• Assorted Torx screwdrivers
• Bubble level
Install Stabilizer
Use the instructions below to install the stabilizer plate on the rack:
1. Use a 3/4 in. wrench to lower the rack leveling pads, and while adjusting the pads use a
bubble level to verify the rack is plum and level.
2. Use a 1/2 in. wrench to install the stabilizer on the front of the rack.
Note: The stabilizer must remain connected to the rack. It should only be removed
when you are relocating the rack.
1. Stabilizer
2. Mounting screw (4X)
3. Leveling pad
C5325
5
1
3
2
- 9840 Tape Drive 1
- List of Pages 5
- Summary of Changes 6
- 95741 Sixth Edition vii 9
- Contents 10
- 95741 Sixth Edition ix 11
- Reader’s Comment Form 12
- 95741 Sixth Edition xi 13
- 95741 Sixth Edition xiii 15
- ■ Organization 17
- ■ Comments and Suggestions 18
- ■ Alert Messages 18
- ■ Related Publications 18
- ■ Conventions 19
- ■ Additional Information 20
- ■ FCC Compliance Statement 21
- Japanese Compliance Statement 22
- 95741 Sixth Edition xxi 23
- Introduction 25
- Host Interfaces 26
- Configurations 26
- ■ Desktop Unit 27
- ■ Rack-mountable Drive Tray 27
- ■ CSL Desktop Unit 28
- ■ Rack-mountable CSL 29
- ■ Operator Panels 31
- Standard Operator Panel 32
- Operator Panels 36
- 1-12 Sixth Edition 95741 36
- Unload switch 37
- Tape Bar 38
- 10% 20% 30% 40% 50% 39
- Cartridges 42
- 1-18 Sixth Edition 95741 42
- Safety and Handling 43
- Lifting Techniques 44
- ESD Precautions 45
- Ω, and the coil cord 46
- Ω. Repair or replace the 46
- ESD-Protection Procedure 46
- ■ Fiber Optic Safety 47
- ■ Laser Product Label 48
- ■ Fiber-Optic Cable Handling 48
- 95741 Sixth Edition 2-7 49
- 2-8 Sixth Edition 95741 50
- Installation 51
- ■ Unpacking the Shipment 52
- ■ Inspecting the Equipment 52
- Inspecting the Equipment 54
- 3-4 Sixth Edition 95741 54
- 95741 Sixth Edition 3-5 55
- Considerations 56
- Cascading Fibre Channel Hubs 56
- Figure 3-4. Cascading Hubs 57
- ■ 9738 Library Attachment 58
- Prepare and Install the Drive 59
- Install Power Supplies 61
- Install Host Interface Cables 63
- 9738 Library Attachment 64
- 3-14 Sixth Edition 95741 64
- 1. Fibre Channel Cable 64
- 9738 Library SCSI Cable(s) 66
- Apply Power to Library Drive 68
- Install a Cleaning Cartridge 68
- ■ Desktop Units 69
- CSL Shipping Insert 70
- SCSI Cables (Desktop/CSL) 73
- Rack Safety and Precautions 76
- Installation Overview 77
- Tools Required 78
- Install Stabilizer 78
- Open the Rear Door 79
- 3-30 Sixth Edition 95741 80
- 1. Captive nut 80
- 95741 Sixth Edition 3-31 81
- 1. Nut plate 81
- 2. Screws (2) 81
- CSL Tray Nuts and Nut Plates 82
- Install Slide Rails 83
- 95741 Sixth Edition 3-35 85
- 3-36 Sixth Edition 95741 86
- 1. Hand tool 86
- 2. Captive nut 86
- CSL Tray Additional Hardware 87
- ■ Rack-mountable Tray 88
- CSL Tray Rail 89
- Insert Tray 90
- Drive Tray 91
- Rack-mountable Tray 92
- 3-42 Sixth Edition 95741 92
- 1. Shipping insert 92
- CSL Tray 93
- Attach Tray Power Cord 95
- 3-48 Sixth Edition 95741 98
- 1. Power cord 98
- 2. Fibre Channel cable 98
- SCSI Cables (Rack-mount Tray) 99
- CAUTION: 100
- Power-On Rack 102
- ■ Configure the Drive 103
- ■ Manually Load Cartridges 104
- ■ Return System to Operator 104
- Getting Started 105
- Reset the Drive 106
- Power-off the Drive 106
- Place the Drive Offline 107
- Place the Drive Online 107
- View Drive Configuration 108
- View Firmware Release Level 108
- ■ Clean the Drive 109
- ■ Cartridges 110
- Load a Cartridge Tape 111
- Unload a Cartridge Tape 112
- Format a Diagnostic Dump Tape 114
- ■ Diagnostic Dump to Tape 115
- Diagnostic Dump to Tape 116
- 4-12 Sixth Edition 95741 116
- Cartridge Scratch Loader 117
- Cartridge Routing 119
- CSL Firmware Update/Load 120
- ■ Desktop CSL 121
- 5-6 Sixth Edition 95741 122
- 1. StorageTek RACK001 122
- ■ Rack-mount CSL Tray 123
- ■ Operator Panel 124
- CSL Switches 125
- ■ Power On/Off CSL 128
- Power Off 129
- Cartridge Loading 130
- Cartridge Unloading 131
- ■ Modes of Operation 132
- Mount Message 133
- Unload Message 133
- Place CSL in System Mode 133
- Automatic Mode 134
- Manual Mode 135
- Priority Mount Mode 136
- CSL in Automatic Mode 137
- CSL in Manual Mode 138
- ■ Error and Recovery 139
- Drive Failure to Load 140
- Recovery Process 141
- Failure to Unload Cartridge 142
- Clearing CSL Errors 143
- Fault Symptom Codes 144
- 95741 Sixth Edition 5-29 145
- Error and Recovery 145
- Start switch once 145
- Load or Start 145
- ■ Jammed Cartridge 146
- ■ Shipping Insert 151
- Install and Lock 153
- Shipping Insert 156
- 5-40 Sixth Edition 95741 156
- Menu System 157
- ■ Menu Structure Overview 159
- ■ Menu Operations 160
- 95741 Sixth Edition 6-5 161
- Menu Operations 161
- Offline Main Menu Operation 162
- ■ Explanation of Menu Trees 164
- (Select Online) 165
- 6-10 Sixth Edition 95741 166
- 95741 Sixth Edition 6-11 167
- 6-12 Sixth Edition 95741 168
- 95741 Sixth Edition 6-23 179
- 6-24 Sixth Edition 95741 180
- 95741 Sixth Edition 6-25 181
- ■ Drive Operations Menu 190
- ■ Dislodge a Stuck Tape 198
- 95741 Sixth Edition 7-3 199
- Dislodge a Stuck Tape 199
- 7-4 Sixth Edition 95741 200
- 95741 Sixth Edition 7-5 201
- 7-6 Sixth Edition 95741 202
- 95741 Sixth Edition 7-7 203
- 7-8 Sixth Edition 95741 204
- Unload switch was 204
- Explanation of Operations 205
- Save Fails Error 206
- Fix_CfgErr Error 206
- 95741 Sixth Edition 7-11 207
- ■ UnWr xxxx Indication 208
- ■ DumpAgain? Indication 208
- Servicing the Drive 209
- Jammed Cartridge 210
- 8-2 Sixth Edition 95741 210
- 1. Turn MUD screw clockwise 210
- 2. Screwdriver 210
- ■ Clean Tape Path 211
- Fibre Channel Transmission 212
- Cleaning Materials 212
- Fibre Channel Cable 212
- 95741 Sixth Edition 8-5 213
- 1. Fibre Channel Ports 213
- Fibre Channel GBIC 214
- Fibre Channel Hub Slot 215
- ■ Fibre Channel Loop Test 216
- Specifications 217
- A-2 Sixth Edition 95741 218
- ■ Environmental Requirements 219
- Cartridge Tapes and Media 220
- Cartridge Tape Specifications 221
- ■ Drive Performance 222
- ■ Host Interfaces 223
- ■ Library Attachments 223
- ■ Supported Device Modes 224
- Glossary 225
- Numerics 231
- Index-2 Sixth Edition 95741 232
- 95741 Sixth Edition Index-3 233
- Index-4 Sixth Edition 95741 234
- 95741 Sixth Edition Index-5 235
- Index-6 Sixth Edition 95741 236
- 95741 Sixth Edition Index-7 237
- Index-8 Sixth Edition 95741 238
- 95741 Sixth Edition Index-9 239
- Index-10 Sixth Edition 95741 240
- 95741 Sixth Edition Index-11 241
- Index-12 Sixth Edition 95741 242
- 95741 Sixth Edition Index-13 243
- Index-14 Sixth Edition 95741 244
- 95741 Sixth Edition Index-15 245
- Index-16 Sixth Edition 95741 246
- BUSINESS REPLY CARD 248
- World Headquarters 250
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 3.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern